|
|
E-Z-GO ELECTRIC MOTORS & PARTS
S&H WILL BE ADDED DURING CHECKOUT, ON SOME HEAVIER ITEMS S&H MAY BE MORE THAN STATED
SCROLL DOWN FOR ELECTRIC MOTORS
| PART# | DESCRIPTION | PRICE |
 #313
'CLICK PICTURES FOR LARGER VIEW |
Insulator kit for new style GE motors | $25.50 |
 #501 |
brush set 1-3/16"x5/8"x1/2" deep | $50.00 set of 4 |
 #502 |
brush set 1-3/4" x 5/8" 1/2" deep | $38.00 set of 4
|
 #506 |
copper crossover without pad | $39.00
|
 #507 |
copper crossover with pad | $38.00 |
 #509 |
brush set 1-7/16"x5/8"x1/2" deep |
$30.00 set of 4 |
 #512 |
brush set 1-7/16"x5/8"x1/2" deep for electric 1980-92 | $55.00 set
|
 #513 |
crossover stud | $34.00 |
 #514 |
brush rigging with springs for electric 1980-92 | $60.00 |
 #515 |
brush holder with springs and crossover studs | $98.00 |
 #516 |
field coil motor repair stud 5/16"-18x1-5/8" long weld on motor repair stud | $40.00 pkg of 10 |
 #521 |
brush holder with springs and copper crossovers | $105.00 |
 #523 |
fiber washer with .425 hole | $44.00 pkg of 20 |
 #524 |
fiber washer with .330 hole | $41.00 pkg of 20 |
 #525 |
fiber washer with .330 hole | $54.00 pkg of 20
|
 #526 |
insulating bushing with .335 hole and .345 thick | $60.00 pkg of 20
|
 #527 |
insulating bushing with .335 hole and .227 thick | $54.00 pkg of 20 |
 #536 |
round insulator with 5/16" hole for electric 1997-up | $49.00 pkg of 20
|
 #537 |
square motor brush insulator for electric 1997-up | $49.00 pkg of 20 |
 #540 |
brush set includes hardware for electric 1997-up | $47.00 |
|
2 sets of 2 required =4 total
|
brush assembly for new style GE motors 2 each required of this set |
$58.00 set |
 #548 |
field coil and brush repair stud 5/16"-18 coarse threads screw on repair stud | $24.00 pkg of 5 |
 #716 |
1/4"-20 brass jam nut | $10.00 pkg of 20 |
|
|
GE electric motor coupler (19 spline) for electric 1988-96 | $21.00 |
|
|
4 hp field coils for new style GE motors | $190.00 |
|
#MOT-B1
|
For E-Z-GO 36 volt Electric 1989-up TXT
NON-REGEN 19 splined Axles Speeds up to 19MPH, 8.0 peak HP,
Replaces D-31, HT-D297, & ADC-6224C Motors.
|
$538.00
|
|
|
FOR E-Z-GO 36 volt Electric DCS/PDS,
Speeds up to 21MPH 8.4 peak HP, Replaces 6-224H & XP-2140 motors.
CONTROLLER UPGRADE REQUIRED MINIMUM 400 AMP REQUIRED |
$618.00 |
|
|
FOR E-Z-GO 36 Volt NON-REGEN Electric 19 splined axles HIGH TORQUE MUST UPGRADE CONTROLLER MINIMUM 400 AMP CONTROLLER REQUIRED | $638.00 |
|
#3807 |
drive end pinion shaft motor | $80.00 |
 #3851 |
commutator end bearing for electric 1980-92 | $6.50 |
 #3852 |
Sealed bearing | $15.00 |
 #3856 |
commutator end bearing pinion shaft motor | $12.00 |
 #3859 |
commutator end bearing for electric 1997-up | $14.00 |
 #3919 |
drive end motor seal for electric 1977-84 | $4.50 |
 #3996 |
motor shaft seal | $16.00 |
 #4309 |
motor brush spring for electric 1980-92 | $20.00 pkg of 10 |
 #4310 |
motor brush spring for #502 brush | $36.00 pkg of 10 |
 #4759 |
motor gasket pinion shaft side to rear end | $1.00 |
 #4834 |
input shaft kit includes shaft, bearings, o'ring, and c-clip for electric 1991-up with 21 tooth gear | $105.00 |
 #5062 |
input shaft kit includes shaft, bearings, o'rings, and c-clip for electric 1988-90 and also 1994-up with 22 tooth gear | $105.00
|
 #5080 |
brush guard for gas 4 cycle 1996-up can be used on TXT | $209.00 |
 #5505
DOESN'T INCLUDE BRUSHES
|
Brush rigging with springs for G.E. motor. For Club Car electric 1994-up 36 & 48-volt. For EZGO with G.E. motor. For Yamaha electric G8, G9, G14 & G16 | $115.00 |
|
|
inductive throttle sensor non dcs for electric 1994-2000 | $152.00
|
|
|
Brush plate assembly with springs. For EZGO electric 1997-up | $175.00 |
#5558